Trubolt® Wedge Anchors - 3/4" Model
GENERAL INFORMATION PAGE
Information Subject to Change without Notice
Not Used on All Target Lifts
Dependable
|
Wedge Type Anchors — SPECIFIED FOR ANCHORAGE INTO CONCRETE  Wedge anchors feature a type 18-8 stainless steel split expansion ring and a threaded stud bolt body and integral cone expander, nut and washer. Anchor bodies are made of plated carbon steel, hot-dipped galvanized carbon steel, type 304 stainless steel or type 316 stainless steel as identified in the drawings or other notations. The exposed end of the anchor is stamped to identify anchor length. Stampings should be preserved during installation for any subsequent embedment verification. Use carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994 to install anchors. Anchors tested to ASTM E488 criteria and listed by ICC (formerly ICBO) and SBCCI. Anchors are listed by the following agencies as required by the local building code: UL, FM, City of Los Angeles, California State Fire Marshal and Cal Trans. |
|||||
|
||||||
|
||||||
|
||||||||||||||||
Catalog Number (TruBolt) |
Trubolt® Zinc Plated Carbon Steel Wedge Anchors |
||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Thread Length |
Anchor Dia. & Drill Bit Size (Threads per Inch) |
Overall Length |
Maximum Thickness of Material To Be fastened |
Qty/Wt Per Box |
Qty/Wt Per Master Carton |
||||||
Inches |
(mm) |
Inches |
(mm) |
Inches |
(mm) |
Qty |
Lbs |
Qty |
Lbs |
||
WS-3454 |
3 |
(76.2) |
3/4-10 |
5-1/2 |
(139.7) |
1-1/2 |
(38.1) |
10 |
8.1 |
50 |
41 |
| Meets ASTM B633 SC1, Type III specifications for electroplating of 5um = .0002" thickness. This material is well suited for non-corrosive environments. | |||||||||||
GENERAL INSTALLATION STEPS |
|
 |
1. Using a bit whose diameter equals the anchor diameter, drill hole to any depth exceeding the minimum embedment. Clean hole. |
 |
2. Assemble anchor with nut and washer so that the top of the nut is flush with the top of the anchor. Drive anchor through material to be fastened so that nut and washer are flush with surface material. |
 |
3. Expand anchor by tightening nut 3 to 5 turns, or to the specific torque requirement (see selection chart below). |
Trubolt Wedge Anchor |
|||||||||
|
ANCHOR TYPE |
ANCHOR DIAM-ETER In. (mm) |
INSTALL-ATION
TORQUE Ft. Lbs (Nm) |
EMBEDMENT
DEPTH In. (mm) |
Ultimate Tension and Shear Values (Lbs/kN) in Concrete* |
|||||
f'c = 2000 PSI (13.8 MPa) |
f'c = 4000 PSI (27.6 MPa) |
f'c = 6000 PSI (41.4 MPa) |
|||||||
TENSION Lbs. (kN) |
SHEAR Lbs. (kN) |
TENSION Lbs. (kN) |
SHEAR Lbs. (kN) |
TENSION Lbs. (kN) |
SHEAR Lbs. (kN) |
||||
WS-Carbon or WS-G Hot-Dipped Galvanized or WW-304 S.S. or SWW-316 S.S. |
3/4 (19.1) |
175 (237.3) |
3-1/4 (82.6) |
7,120 (31.7) |
10,120 (45.0) |
10,840 (48.2) |
13,720 (61.0) |
13,300 (59.2) |
15,980 (71.1) |
| 6-5/8 (168.3) | 10,980 (48.8) | 20,320 (90.4) | 17,700 (78.7) | 23,740 (105.6) | 20,260 (90.1) | 23,740 (105.6) | |||
| 10 (254.0) | 10,980 (48.8) | 20,320 (90.4) | 17,880 (79.5) | 23,740 (105.6) | 23,580 (104.9) | 23,740 (105.6) | |||